background image

www.desatech.com

114370-02C

4

Keep the log set area clear and 

free from combustible materials, 

gasoline  and  other  flammable 

vapors and liquids.

Children  and  adults  should  be 

alerted to the hazard of high tem-

perature and should stay away to 

avoid burns or clothing ignition.

1.  Do not place propane/LP supply tank(s) in

-

side any structure. Locate propane/LP supply 

tank(s) outdoors (propane/LP units only).

2.  If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use 

any phone in your building

• immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 

instructions

• if you cannot reach your gas supplier, call 

the fire department

3.  Never install the log set

• in a recreational vehicle

• where curtains, furniture, clothing or other 

flammable objects are less than 42" from the 

front, top or sides of the log set.

• in high traffic areas

• in windy or drafty areas 

4.  Before installing in a solid fuel burning fire

-

place, the chimney flue and firebox must be 

cleaned of soot, creosote, ashes and loose paint 

by a qualified chimney cleaner. Creosote will 

ignite if highly heated. Inspect chimney flue 

for damage. If damaged, repair flue before 

operating appliance.

5.  Do not operate heater if any log is broken. Do 

not operate heater if a log is chipped (dime-

sized or larger).

6.  This log set is designed to be smokeless. If 

logs ever appear to smoke, turn off appliance 

and call a qualified service person. 

Note:

 

During initial operation, slight smoking could 

occur due to log curing and the burning of 

manufacturing residues. You may wish to add 

more ventilation by opening a window.

7.  To reduce the creation of soot, follow the instruc

-

tions in 

Cleaning and Maintenance

, page 12.

SAFETy INFORMATION

Continued

8.  The installation and provisions for combustion 

and ventilation air must conform with the 

Na-

tional Fuel Gas Codes, ANSI Z233.1/NFPA 54, 

Section 5.3, Air for combustion and Ventilation.

9.  To prevent performance problems, do not 

use propane/LP fuel tank of less than 100 lb. 

capacity (propane/LP units only).

10.  Do not run log set

• where flammable liquids or vapors are used 

or stored

• under dusty conditions

11.  Do not burn solid fuel in the fireplace after 

installing the log set. Do not use this log set 

to cook food or burn paper or other objects.

12.  Do not use heater if any part has been exposed 

to or under water. Immediately call a qualified 

service technician to inspect the room heater 

and to replace any part of the control system and 

any gas control which has been under water.

13.  Turn log set off and let cool before servicing, 

installing or repairing. Only a qualified service 

person should install, service or repair log set.

14.  Provide  adequate  clearances  around  air 

openings.

PRODUCT 

IDENTIFICATION

 WARNING: Failure to posi-

tion  the  parts  in  accordance 

with  these  diagrams  or  failure 

to  use  only  parts  specifically 

approved  with  this  appliance 

may result in property damage 

or personal injury.

Figure 1 - Product Identification

Log Set
Assembly

Grate

Chassis 
Assembly

Ceramic 
Burner

Control 
Knob

Piezo 
Ignitor

ON/OFF 
Switch

Summary of Contents for Design Dynamics VTD-18NV-JHB





















Reviews: