background image

www.desatech.com

114370-02C

9

INSTALLATION

Continued 

CHECKING GAS CONNECTIONS

 WARNING: Test all gas piping 

and  connections,  internal  and 

external to unit, for leaks after 

installing or servicing. Correct 

all leaks at once.

  WARNING:  Never  use  an 

open flame to check for a leak. 

Apply a noncorrosive leak detec-

tion fluid to all joints. Bubbles 

forming show a leak. Correct all 

leaks at once.

  CAUTION:  Make  sure  ex-

ternal  regulator  has  been  in-

stalled  between  propane/LP 

supply  and  appliance.  See 

guidelines under 

Connecting to 

Gas Supply

, page 7.

PRESSURE TESTING GAS SUPPLY 
PIPING SYSTEM 
Test Pressures In Excess Of 1/2 PSIG 
(3.5 kPa)

1.  Disconnect  appliance  with  its  individual 

equipment  shutoff  valve  from  gas  supply 

piping system. Pressure in excess of 1/2 psig 

will damage appliance regulator.

2.  Cap off open end of gas pipe where equipment 

shutoff valve was connected.

3.  Pressurize supply piping system by either 

opening propane/LP supply tank valve for 

propane/LP gas or opening main gas valve 

located on or near gas meter for natural gas, 

or using compressed air.

4.  Check all joints of gas supply piping system. 

Apply noncorrosive leak detection fluid to gas 

joints. Bubbles forming show a leak. 

5.  Correct all leaks at once.

6.  Reconnect  log  set  and  equipment  shutoff 

valve to gas supply. Check reconnected fit

-

tings for leaks. 

Test Pressures Equal To or Less Than 
1/2 PSIG (3.5 kPa)

1.  Close equipment shutoff valve (see Figure 8).

2.  Pressurize supply piping system by either us

-

ing compressed air or opening main gas valve 

located on or near gas meter.

3.  Check all joints from gas meter to equipment 

shutoff valve for natural gas or propane/LP 

supply to equipment shutoff valve for propane/

LP (see Figure 9 or 10). Apply noncorrosive 

leak detection fluid to all joints. Bubbles form

-

ing show a leak. 

4.  Correct all leaks at once.

Figure 8 - Equipment Shutoff Valve

Equipment 
Shutoff 
Valve

Open

Closed

Figure 9 - Checking Gas Joints  

(Propane/LP Gas Only) 

Figure 10 - Checking Gas Joints  

(Natural Gas Only) 

Gas Meter

Propane/LP 
Tank

Equipment 
Shutoff Valve

Equipment 
Shutoff Valve

Control Valve 
Location

Control Valve 
Location

Summary of Contents for Design Dynamics VTD-18NV-JHB





















Reviews: