background image

14

107064

UNVENTED PROPANE/LP GAS FIREPLACE

LFP33PRA

INSTALLATION

Continued
OPTIONAL WIRELESS HAND-
HELD REMOTE CONTROL
ACCESSORY RM4

Installing Remote Receiver Unit

1.

Disconnect switch wires from the con-
trol valve.

2.

Remove screws and nuts attaching
switchplate. Save screws and nuts to
attach receiver.

3.

Remove switch plate (see Figure 27).
Discard after removing.

4.

Install remote receiver unit onto remote
switch bracket using screws and nuts
removed in step 2. See Figure 28.

5.

Route wires through hole in the upper
portion of the switch plate (Figure 28).
Connect wires as shown in Figure 29.
(Black and blue wires are not used for
this application.)

Figure 27 - Switch Plate and Wiring
Harness

Figure 30 - Installing Battery in Remote
Receiver

Screw

Switch Plate

Wires

Figure 28 - Installing Remote Receiver

Installing Batteries in Hand-Held
Remote Control Unit

1.

Remove battery cover on front of re-
mote control unit following direction
of arrow.

 2. Insert two AAA batteries following dia-

gram in battery housing area.

3.

Replace battery cover onto remote con-
trol unit.

Figure 31 - Installing Battery in Hand-
Held Remote Control Unit

AAA
Batteries

Battery
Cover

Remote
Control Unit

Battery
Housing

Figure 29 - Connecting Wires

Red Wire From
Receiver

Valve

White Wire
From Receiver

INSTALLING BATTERIES
FOR RM4

Four AA and two AAA batteries (not in-
cluded) are required to operate this heater
with the wireless hand held remote control
set. AA batteries must be installed in the
receiver and AAA batteries in the hand-held
remote control unit. 

Note:

 Only use alka-

line batteries.

Installing Batteries in Receiver

1.

Locate back of receiver behind the re-
mote switch bracket under the firebox
bottom.

2.

Slide the battery door off of the receiver
in the direction of the arrow on the door.

3.

Insert the four AA batteries according
to Figure 30.

4.

Slide the battery door back into position.

Remote Receiver

Screws

Remote Switch
Bracket

Battery Door

AA Batteries

Remote
Receiver

Ignitor

Nuts

Terminal
Wires

+

+

-

-

-

+

+

+

-

-

+

Summary of Contents for Comfort Glow LFP33PRA































Reviews: