www.desatech.com
119635-01B
6
WARNING: If the information
in these instructions is not fol-
lowed exactly, a fire or explosion
may result causing property dam-
age, personal injury or death.
Do not store or use gasoline or
other flammable vapors in the vi-
cinity of this or any other heater.
INSTALLING AS A FIREpLACE
Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and
high traffic areas.
Note:
Follow all national and
local electrical codes. This insert can be installed
into either an existing fireplace or as new construc
-
tion/renovation.
NOTICE: Never pick unit up by
louvers. Louvers will bend.
Existing Fireplace Installation
1. Thoroughly clean out the existing fireplace
and hearth area.
2. Seal all drafts, vents or ash clean-outs with fiber
-
glass insulation. Seal the flue. Once sealed, close
damper to stop debris from falling onto unit.
3. If existing fire box is susceptible to moisture, cap
the top of the chimney flue to prevent infiltration
of water.
Note:
It is strongly advised that you
hire a qualified professional to undertake this
step in order to prevent personal injury. Once the
flue is capped, the chimney is no longer suitable
for wood burning.
Note:
Do not install this unit
into a fireplace that is prone to dampness; the
area of installation must be dry.
4. Plan the power supply.
Units with a power chord
:
If an existing
grounded outlet is near the fireplace, the power
cord can run along the front of the fireplace.
If the cord is not long enough to reach the
outlet, a grounded extension cord minimum
AWG No. 14 and rated to a minimum of 1875
watts, may be used. If you plan to cut or drill
a hole in the existing fireplace for wiring, it
is best to hire a professional to do this step in
order to prevent personal injury. To reduce the
risk of fire, do not run the power cord under
rugs, carpets, etc. Arrange the power supply
cord away from high traffic areas where it may
pose a tripping hazard.
Unit to be hardwired:
This fireplace must
be installed by a qualified (certified or li
-
censed) service person. It can be wired for
120 V 1600 W or 240 V 3000 W (see
Wiring
Diagram
, page 10).
WARNING: The solid fuel/gas
fireplace has been converted for
use with an electric insert and
cannot be used for original fuels
unless all original parts have
been replaced and the fireplace
has been reapproved by the au-
thority having jurisdiction.
New Construction or Renovation
1. Select a location that is not prone to moisture
and is located at least 0.9 m or 3 feet away
from combustible materials such as curtains
or drapes, furniture, bedding, paper, etc.
2. Place unit in selected location to see how it
will look in the future.
3. Mark the desired location on the floor and store
unit in a safe, dry and dust free location.
4. Frame in an opening leaving at least 1/4" (6 mm)
around the edge of the unit. Any new wiring
must be done in compliance with local and
national codes and other applicable regula-
tions in order to reduce the risk of fire, electric
shock or other injuries. Therefore, it strongly
recommended that you hire a professional to
complete any such work.
5. Plan you power supply. See step 4 of
Existing
Fireplace Installation.
Installing Insert
Once the site has been prepared, the fireplace insert
can be installed.
1. Install the trim onto the front of the unit.
2. Make sure switch is in the OFF position.
3. Plug fireplace into a 15-amp/120 volt,
grounded outlet.
4. Push fireplace insert so that the trim is against
the finished mantle or wall surface.
NOTICE: When the front is
installed it will cover the gap
between the heater and framing,
cabinet, finishing materials or
existing fireplace.
INSTALLATIoN
Continued
