ENGLISH
9
• The supplied remote control unit (RC-999) is for use with the RCD-M33 unit only.
• If the cassette deck is connected to the main unit, you may operate each of the above components
using its respective remote control unit (refer to pages 9, 10).
7
REMOTE CONTROL UNIT
(1) Inserting the batteries
q
Open the battery compartment cover of the
remote control unit.
Press the knob and open the cover in the
direction of the arrow.
w
Insert the two R03 (AAA) batteries, following
the + and – marks in the battery compartment.
e
Close the cover of the battery compartment.
Cautions on Batteries
• Use R03 (AAA) batteries in this remote
control unit.
• Replace the batteries with new ones after
approximately 1 year, though this depends
on the frequency with which the remote
control unit is used.
• Replace the batteries with new ones if the
unit does not operate when the remote
control unit is operated from nearby, even if
the batteries are less than a year old.
• Be sure to insert the batteries in the proper
direction, following the “
<
” and “
>
”
marks in the battery compartment.
• To avoid damage or leakage of battery fluid:
• Do not use a new battery with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, take apart, heat or
dispose of batteries in flames.
• Remove the batteries when you do not plan
to use the remote control unit for an
extended period of time.
• If the battery fluid should leak, carefully wipe
off the fluid from the inside of the battery
compartment, then insert new batteries.
(2) Using the Remote Control Unit
• The remote sensor is located on the CD receiver.
Point the remote control unit at the remote
sensor as shown on the diagram when operating
it.
• The remote control unit will operate from a
direct distance of approximately 7 meters, but
this distance will be shortened if obstacles are
present or if operated at an angle. (The remote
control unit will operate at an angle of up to 30°
in either direction.)
7m
30
°
30
°
NOTES:
• The remote control unit may not operate if
the remote sensor is exposed to direct
sunlight or the strong light from a lighting
fixture, or if there is an obstacle between the
remote control unit and the remote sensor.
• Do not press buttons on the remote control
unit and on the set at the same time. Doing
so could result in malfunctions.
• If the remote control unit is pointed away
from the re-mote sensor during continuous
operations (such as when turning the volume
up or down), the operation will stop. If this
happens, point the remote control unit at the
remote sensor and press the button again.
The RCD-M33 comes with a system remote control unit (RC-999).
q
e
#5
w
r
t
y
u
i
o
!0
!1
!2
!3
!4
!5
!6
!7 !8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
@9
#0
#1
#2
#3 #4
(3) Remote Control Unit Part Names and Functions
q
SLEEP button
• Press this button to set the sleep timer.
w
OFF button
• Use this switch to set the power to
STANDBY mode.
e
TUNER button
• Press this button to set the function
TUNER mode.
r
CD button
• Press this button to set the function CD
mode.
t
PROG/DIRECT button
• Press this button to switch between
PROGRAM and DIRECT play.
y
EDIT button
In CD function :
• Press this button for edited recording on a
tape, dividing the tracks onto sides A and
B according to the length of the tape.
In TUNER function :
• Press this button to input the station
name.
u
CALL button
• Use this button to confirm the
programmed song.
i
Number buttons
In CD function :
• Press these buttons to specify the
desired track.
In TUNER function :
• Press these buttons to recall preset
station.
o
FOLDER (+ / –) button
For MP3/WMA discs with the function set
to CD:
• Select the folder.
• In the play and pause modes, the first
track in the selected folder is selected.
1.RCD-M33-E3-ENG 05.4.13 5:46 PM ページ 9
