background image

 
 
 
 

 

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY 
EXERCISING ON THIS EQUIPMENT.  THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS 
FOLLOWING THESE SIMPLE RULES: 
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL 
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU. 
2)  STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM- PROPER STRETCHING WILL PREPARE YOUR 
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES. 
3)  IF AT ANY TIME YOU SHOULD FEEL FAINT, DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER 
ABNORMAL SYMPTOMS OR DISCOMFORT, DISCONTINUE USE AND CONSULT YOUR DOCTOR. 
4)  DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER 
WORK OUT ALONE -ALWAYS HAVE A PARTNER. 
5)  SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT 
LOOSENED. 
6)  WEAR GOOD RUBBER SOLE SHOES ONLY DO NOT USE BARE FOOTED OR WITH SOCKS ONLY. 
7)  DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH 
COULD BECOME ENTANGLED IN MOVING PARTS. 
8)  DO NOT STAND OR KNEEL ON SEAT ALWAYS SIT OR LAY SQUARELY CENTERED. 
9)  KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES. 
10)  CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF 
POSSIBILITY OF INJURY FROM IMPROPER USAGE.  THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.  
11)  REPLACEMENT OR WORN OR DEFECTIVE PARTS MUST BE REPLACE WITH FACTORY AUTHORIZED 
PARTS.  IF OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES 
AND LIABILITIES BECOME VOID. 

SAFETY NOTICE 

 

Summary of Contents for DF830



















Reviews: