background image

3

Quick installation guide for RPI M50A inverters

General safety instructions

1

DANGER

Risk of death by electrocution

Potentially fatal voltage is applied to the solar 
inverter during operation  This potentially fatal 
voltage is still present for 10 seconds after all 
power sources have been disconnected 

 

Never open the solar inverter  

 

Always disconnect the solar inverter from 
power before installation, open the AC/DC 
isolating switch and make sure neither can 
be accidentally reconnected 

 

► Wait at least five minutes until the capacitors 

have discharged 

DANGER

Risk of death or serious injury from elec-
trocution

Potentially fatal voltage may be applied to the 
DC connections of the solar inverter  When light 
is falling on solar modules, they immediately start 
producing energy  They do so, even when the 
sun is not shining 

 

Never disconnect the solar modules when the 
solar inverter is powered  

 

First switch off the grid connection so that 
the solar inverter cannot feed energy into the 
grid  

 

Turn the AC/DC isolating switch to position 

OFF

 

 

Make sure the DC connections cannot be 
accidentally touched 

 

The solar inverter can be safely and normally operated if 
installed and used in accordance with this manual (see 
IEC 62109-5 3 3)  Delta Energy Systems is not responsible 
for damage incurred by failure to observe the installation and 
operating instructions in this manual  For this reason, be sure 
to observe and follow all instructions!

 

Installation and commissioning may only be performed by 

qualified electricians using the installation and commission

-

ing instructions found in this manual 

 

The solar inverter must be disconnected from power and the 
solar modules before any work on it can be performed 

 

The solar inverter has a high leakage current value  The 
ground wire 

must

 be connected before commissioning 

 

Do not remove any warning signs that the manufacturer has 
installed on the solar inverter 

 

Improper handling of the solar inverter may result in physical 
injury and damage to property  For this reason, observe and 
follow all general safety instructions and warnings 

 

The solar inverter contains no components that must be 
maintained or repaired by the operator or installer  All repairs 
must be performed by Delta Energy Systems  Opening the 
cover will void the warranty 

 

Do not disconnect any cables when the solar inverter is pow-
ered due to risk of a fault arc 

 

To prevent lightning strikes, follow the relevant regulations 
applicable in your country 

 

The surface of the solar inverter can become very hot dur-
ing operation  Use safety gloves when working on the solar 
inverter 

 

The solar inverter is very heavy  The solar inverter must be 
lifted and carried by at least three people  

 

Only devices in compliance with SELV (EN 69050) may be 
connected to the RS485 and USB interfaces 

 

All connections must be sufficiently insulated in order to com

-

ply with the IP65 protection rating  Unused connections must 
be closed by placing cover caps on the solar inverter 

Summary of Contents for RPI M50A 120





















Reviews: