background image

16

Quick installation guide for RPI M6A M8A M10A inverters

Setting a power limitation

E - T o d a y :                 0 k W h

P o w e r :                       0 W

S t a t u s :             O n   G r i d

    1 0 . S e p   2 0 1 4   1 5 : 3 2

1. 

When the default information is displayed, press any button to open the main menu 

I n v e r t e r   I n f o .
G e n e r a l   S e t t i n g s
I n s t a l l   S e t t i n g s
A c t i v e / R e a c t i v e   P w r  
F R T

2. 

Use the buttons 

 and 

 to select 

Active/Reactive Pwr

 

To confi rm your selection, press the button 

ENT

 

Because a power limitation reduces your yield, you should set a power limitation only when requested by 
country regulations, authorities or your grid operator  
This setting is protected by a special password  To get the password, please call the Delta Support hotline 

in your country. You can fi nd the telephone number on the last page of this quick installation guide.

 

          0   *   *   *

          P a s s w o r t

 

3. 

Type in the password you received from Delta Support  Use the buttons 

 and 

 

to set each digit 

To confi rm a digit, press the button 

ENT

  

 

 

R e a c t i v e   P o w e r   C t r l

A c t i v e   P o w e r   C t r l

4. 

Use the buttons 

 and 

 to select 

Active Power Ctrl

 

To confi rm your selection, press the button 

ENT

 

 

P ( V )

P o w e r   v s .   F r e q u e n c y

P o w e r   l i m i t

5. 

Use the buttons 

 and 

 to select 

Power limit

 

To confi rm your selection, press the button 

ENT

 

 

 

S e t   P o i n t :           1 0 0 %

M o d e :                       O F F

6. 

Use the buttons 

 and 

 to select 

Mode

 

To change the value, press the button 

ENT

 

 

 

S e t   P o i n t :           1 0 0 %

M o d e :                         O N

7. 

Use the buttons 

 and 

 to change the value to 

ON

  This will switch on the func-

tion “Power limit” 

To confi rm your selection, press the button 

ENT

 

 

 

S e t   P o i n t :           1 0 0 %

M o d e :                         O N

8. 

Use the buttons 

 and 

 to select 

Set Point

 

To change the value, press the button 

ENT

 

Use the buttons 

 and 

 to change the value 

To confi rm the value, press the button 

ENT

 

Commissioning - Further Settings (continued)

12

Other settings for active and reactive power control are described in the full installation and operation 
manual that you can download from the Delta website 

Summary of Contents for RPI M10A





















Reviews: