Delta MOOVair User Manual Download Page 38

Page: 38 / 40

useful for debug purposes.

Type

Fault/Status

CAN

Report

Active

Deactive

Status

Chrgr_Prof_

ChargeEnd

0x5Dx,

bit8

Charge has ended due to

Status

Chrgr_Prof_Phase_

AhLim

0x5Dx,

bit10

The number of amp hours

returned to the battery is too

high for the charging stage.

Remove source of fault and

recycle DC on the WSB

Status

Chrgr_Prof_Phase_

Imax

0x5Dx,

bit11

Current has exceeded the

maximum allowed by the

Status

Chrgr_Prof_Phase_

Imin

0x5Dx,

bit12

Current is below the

minimum allowed by the

Status

Chrgr_Prof_Phase_

Timeout

0x5Dx,

bit13

The charge stage is taking

too long.

Remove source of fault and

recycle DC on the WSB

Status

Chrgr_Prof_Phase_

Vmax

0x5Dx,

bit14

Voltage has exceeded the

maximum allowed by the

Status

Chrgr_Prof_Phase_

Vmin

0x5Dx,

bit15

Voltage is below the

minimum allowed by the

Status

Chrgr_Prof_

PhaseComplete

0x5Dx,

bit16

Status

Chrgr_Prof_

PhaseError

0x5Dx,

bit17

occurred

Summary of Contents for MOOVair









































Search results

Summary of Contents for MOOVair

Reviews:

Related manuals for MOOVair

Brands by name

Popular brands

Delta MOOVair, User Manual

Search results

Summary of Contents for MOOVair

Reviews:

Related manuals for MOOVair

Brands by name

Popular brands