background image

-      - 

34 

ORDER

 

CODES 

HD2114.0

 

Kit including the instrument HD2114.0 

with built-in 20mbar full scale probe

,

 

x 1.5V alkaline batteries, operating manual, case. 

Other probes must be ordered 

separately.

 

HD2114.2

 

Kit  including  the  instrument  HD2114.2 

datalogger  with  built-in  20mbar  full 

scale  probe

,  4 x 1.5V  alkaline  batteries,  operating  manual,  case  and  DeltaLog9 

software. 

Other probes and the cables must be ordered separately.

 

HD2134.0

 

Kit including the instrument HD2134.0 

with built-in 200mbar full scale probe

,

 

4  x  1.5V  alkaline  batteries,  operating  manual,  case. 

Other  probes  must  be 

ordered separately.

 

HD2134.2

 

Kit  including  the  instrument  HD2134.2 

datalogger  with  built-in  200mbar  full 

scale  probe

,  4 x 1.5V  alkaline  batteries,  operating  manual,  case  and  DeltaLog9 

software. 

Other probes and the cables must be ordered separately.

 

HD2164.0

 

Kit including the instrument HD2164.0 

with built-in 2000mbar full scale probe

,

 

4 x 1.5V  alkaline  batteries,  operating  manual,  case. 

Other  probes  must  be 

ordered separately.

 

HD2164.2

 

Kit including the instrument HD2164.2 

datalogger with built-in 2000mbar full 

scale  probe

,  4 x 1.5V  alkaline  batteries,  operating  manual,  case  and  DeltaLog9 

software. 

Other probes and the cables must be ordered separately.

 

HD2114B.0

 

Kit  including  the  instrument  HD2114B.0 

with  600…1100mbar  range 

barometric  sensor

,

 

4 x 1.5V  alkaline  batteries,  operating  manual,  case. 

Other 

probes must be ordered separately.

 

HD2114B.2

 

Kit  including  the  instrument  HD2114B.2 

datalogger  with  600…1100mbar 

range barometric sensor

, 4 x 1.5V alkaline batteries, operating manual, case and 

DeltaLog9 software. 

Other probes and the cables must be ordered separately. 

HD2110CSNM

  Connection cable 8-pole MiniDin – Sub D 9-pole female for RS232C. 

C.206

 

Connection  cable  8-pole  MiniDin  –  USB  type  A.  With  integrated  RS232/USB 
converter. 

CP23 

Connection cable Mini-USB type B – USB type A. 

DeltaLog9

 

Software  for  transfer  and  management  of  the  data  on  PC  using  Windows  (from 
98) operating systems. 

SWD10

 

Stabilized power supply at 100-240Vac/12Vdc-1A mains voltage. 

HD40.1 

The kit includes: 24-column portable thermal printer, serial interface, 57mm paper 
width, four  NiMH 1.2V rechargeable batteries, SWD10 power supply, instruction 
manual, 5 thermal paper rolls. 

BAT.40  

Spare battery pack for HD40.1 printer with in-built temperature sensor. 

RCT 

The kit includes 4 thermal paper rolls 57mm wide and 32mm in diameter. 

 

Summary of Contents for HD2114.0









































Reviews: