Delta AlertMaxx Installation & Operating Instructions Manual Download Page 14

Page: 14 / 16

15.0 LED codes

For technical support, please call 01279 757400

AlertMaxx

Beep

Red LED

Blue LED

Green LED

Fault

1/sec

3/sec

High water alarm

1/min

1/5sec

1/sec

Mains failure

Any

Solid

Any

Error - Call support

1/min

Any

1/sec

Any

Service required

2/sec

High water has occurred

1/sec

All OK

All flash in sequence

Battery too low to start up

Various

Solid

Serious internal error

3/sec

Solid

Float cable issues

16.0 Troubleshooting

Fault

Cause

The unit does not turn on.

Battery is flat - charge the battery by connecting

mains supply to alarm unit.

Still doesn’t turn on after 3 mins - alarm unit is

faulty.

The LEDs flash in the following order, red, blue,

green.

Low battery - charge the battery by connecting

mains supply to alarm unit.

The red LED is flashing and the blue LED is solid.

Float switch cable is faulty - check float switch

connections and cable for damage.

Float switch is broken - replace float switch.

Float cable is broken - replace float switch.

The alarm does not activate when the float switch

is lifted.

The alarm does not activate when pressing the

‘TEST’ button

Faulty unit.

Alarm continuously active.

Float has been incorrectly wired - check the cables

are connected correctly.

Finger float has been installed upside down.

Summary of Contents for AlertMaxx

















Search results

Summary of Contents for AlertMaxx

Reviews:

Related manuals for AlertMaxx

Brands by name

Popular brands

Delta AlertMaxx, Installation & Operating Instructions Manual

Search results

Summary of Contents for AlertMaxx

Reviews:

Related manuals for AlertMaxx

Brands by name

Popular brands