background image

11

ENGLISH

O p e r a t i o n

SWITCHING THE APPLIANCE ON

Connect the appliance to the mains supply.
On the display two lines will appear indicating Stand-by mode
Press the ON/OFF button (A) and then the MODE button until the
relevant function indicator appears viz.:

Indicator C 

: air-conditioning

Indicator D

: dehumidifying

Indicator E

: ventilation

AIR-CONDITIONING FUNCTION

This function is ideal in hot, humid weather conditions when the
atmosphere requires to be cooled and dehumidified.
To ensure proper function of the appliance, after selecting the air-
conditioning function, press b (F) or – (G) until the desired
temperature appears on the display.

The temperatures most suited to the atmosphere in summer vary
between 75 °Fand 80°F. We do not advise selection of tempera-
tures much lower than those outside.

Select fan speed by pressing the “FAN” button (Q) until the fan
speed indicator appears:
MAX (P):  if you want the maximum power of the air-conditioner to

reach the desired temperature as quickly as possible.

MIN (O):  if you want to reduce the level of noise and still maintain

a good level of comfort.

SILENT (N):when minimum noise is required,
AUTO (M):if you prefer the appliance to select the fan speed for

the temperature selected on the display panel.

DEHUMIDIFYING FUNCTION

This function is ideal for reducing humidity in the atmosphere while
avoiding increases or decreases in temperature (in between sea-
sons, damp places, wet spells of weather).
When you select the dehumidifying function, the letters “     ” will
appear on the display.

The water is collected in the tank at the rear of the appliance.
When the tank is full, the appliance will stop working and the
display will show the letters “     ” (Full Tank); the tank must then be
emptied. When it is re-inserted, the appliance will re-start auto-
matically. N.B. remove the air exhaust hose (14).

In the air-conditioning function, the unit employs an exclusive con-
densation recycling system to dispose of excess moisture. In normal
conditions, condensation is disposed of automatically. When the
humidity is particularly high, an excess of condensation may built up
in the TANK (9). When this happens, the display  will  show the letters
“     “ (Full Tank); indicating that the TANK  should be emptied.  Whe-
never conditions of high humidity make the problem recurrent, you
may discharge the excess water directly into a drain, using the rub-
ber tube supplied. The tube should be inserted into the hole provi-
ded, after having removed the rubber stopper. (see figure below).
Make sure the TANK  is put back correctly otherwise the display will
continue to show the letters “       ”

GB  8-07-2003  15:32  Pagina 11

Summary of Contents for Pinguino K900
















Reviews: