DeLonghi La Specialista EC9335M, Manual

Page: 38 / 45

37
13.9 Replacing the burrs
When the quantity of coffee becomes even less, contact a cus-
tomer services centre to have the burrs replaced, then adjust the
mill again as follows:
1. Press and hold the
(B3) and (B7) buttons for at
least 3 seconds to access the menu. The (B15) and
(B16) lights alternate;
2. Turn the mode selection dial (B8) to the position. The
light (B14) remains on steadily;
3. Select the original grinding range by pressing the
button;
4. Press the button (B1) to exit the menu. (If the appli-
ance is left idle for about 1 minute, it exits automatically
from the settings menu and is ready for use again);
5. Turn the ground coffee quantity dial (B2) to the "min”
position, then proceed to adjust as though it were the first
time ("4.5 Adjusting the quantity of ground coffee in the
filter").
13.10
Cleaning the "Smart tamping station"
To guarantee top quality grinding, clean the “Smart tamping
station” regularly as follows:
47 48
1. Clean the attachment area
with a brush (fig. 7).
2. Pull the
lever
(A23) as
far as it will go and clean
the presser cylinder with
a brush (fig. 48). Then re-
lease the lever.
3. Use the tube brush (C8)
to clean the coffee guide
(fig. 49).
13.11 Other cleaning operations
1. Do not use solvents or abrasive detergents to clean the cof-
fee maker. Use a soft damp cloth only.
2. Clean the filter holder cup.
3. You are recommended to use De’Longhi detergent.
14. DESCALING
Descale the appliance when the light (B9) comes on.
• Before use, read the instructions and the labelling on the
descaler pack.
• It is important to use De’Longhi descaler only. Using unsuitable
descaler and/or performing descaling incorrectly may result in
faults not covered by the manufacturer's guarantee.
Proceed as follows:
1. (IF PRESENT, REMOVE THE WATER SOFTENER FILTER).
Pour the descaler into the tank up to the level A
marked inside the tank (equal to one 100ml packet), then
add water (litre) up to the level
B
.
2. If the appliance is off, press the ON/Standby button (B1).
3. Make sure the filter holder is not attached and position a
recipient under the spouts (A5), (A6) and the boiler outlet
(A21)
(fig. 8).
4. Turn the mode selector dial (B8) to the position. The
light flashes and the light comes on.
5. Press (B5) to start descaling.
6. The descale programme starts and the descaler liquid comes
out of the spouts and boiler outlet. The descale programme
removes limescale deposits from inside the appliance by au-
tomatically performing a series of rinses and pausesuntil the
tank is empty.
7. Delivery stops and the (B15) and lights corre-
sponding to the rinse button (B4) come on.
8. Empty the recipient used to collect the descaler solution
and replace it empty under the spouts.
9. Remove the water tank, empty any residues of descaler
solution, rinse with running water and fill with fresh water
up to the MAX level. Put the tank back in its housing.
10. Press the button. The appliance rinses the internal
circuits and delivers water from all three spouts.
11. When rinsing is complete, delivery stops. All the LEDs flash
briefly and the appliance prepares to be used again.
12. Empty the recipient used to collect the rinse water.
13. Extract and empty the drip tray, then put back in the
appliance.
14. Extract the tank, fill with fresh water, then put back in the
appliance.
15. Turn the mode selector dial to one of the coffee positions.
49