8
9
DESCRIPTION
Description of the appliance
(page 3 -
A
)
a1.
grinding adjustment knob
a2.
Main switch
a3.
Beans container
a4.
Beans container lid
a5.
Cover for funnel and measure compartment
a6.
Measure compartment
a7.
Cup shelf (cup warmer active, when energy Saving is
disabled)
a8.
Pre-ground coffee funnel
a9.
hot water and steam nozzle
a10. Water tank
a11. Power cable
a12. Cup tray
a13. drip tray
a14. Service door
a15. grounds tray
a16. Coffee spout (adjustable height)
a17. Coffee guide
a18. infuser
a19. Control panel
a20. hot water spout
a21. Measure
a22. Cleaning brush
a23. descaler
a24. reactive strip to detect water hardness (Total hardness
test)
Description of the milk container
(page 3 -
B
)
B1.
lid with milk frother
B2.
Container handle
B3.
Clean button
B4.
Milk intake tube
B5.
Frothed milk spout
B6.
Milk container
Description of control panel
(page 3 -
C
)
A number of buttons on the panel have a dual function. This is
indicated in brackets in the description.
C1.
display: guides the user in using the appliance.
C2.
button: to deliver two cups of coffee
(when
you access the MENU: to scroll backwards through the
menu)
C3.
button: to make 1 cup of coffee
(when you access
the MENU: OK button to enable and confirm the selected
function)
C4.
MENU
button: to access the settings menu.
C5.
button: to turn the appliance on and off (stand-
by)
C6.
button to deliver hot water.
C7.
CAPPUCCINO
button to deliver a cappuccino or
frothed milk (press button twice)
C8.
button: to select coffee quantity
(when
you access the MENU: to scroll forwards through the
menu)
C9.
button: to select coffee taste
(When you access
the MENU: ESC to exit the menu)
C10.
button: to perform a rinse cycle
C11.
button: to select pre-ground coffee
PRElIMINARY CHECKS
Checking the appliance
after removing the packaging, make sure the product is
complete and undamaged and that all accessories are present.
do not use the appliance if it is visibly damaged.
Contact de’longhi Customer Services.
Installing the appliance
Important!
When you install the appliance, you should respect the
following safety warnings:
• The appliance gives off heat. After positioning the
appliance on the worktop, leave a space of at least 3 cm
between the surfaces of the appliance and the side and
rear walls and at least 15 cm above the coffee maker.
• Water penetrating the appliance could cause damage. Do
not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes. do not install the appliance in a room where the
temperature could drop below freezing point.
• Arrange the power cable in such a way that it cannot be
damaged by sharp edges or contact with hot surfaces
(e.g. electric hot plates).
Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to
the value indicated on the rating plate on the bottom of the
appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10a only.
if the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
Using the appliance for the first time
Please note :
• Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the grinder. The machine is, however, guaranteed to be
new.
• you should customise water hardness as soon as possible
following the instructions in the section “Setting water
hardness” on page 17.
1. Plug the appliance into the mains socket and place the
main switch on the back of the appliance in the i position
(fig. 1).
you must first choose the language (the languages scroll
through at intervals of about 3 seconds).
2. When “english” appears, press the
OK
button (fig. 2). once
the language has been saved, the message “engliSh set”
is displayed.
Follow the instructions indicated by the appliance:
3. “FILL TANK”: remove the water tank, fill to the MAX line
with fresh water then replace in the appliance (fig. 3).
4. “inSerT WaTer SPouT”: Check that the hot water spout
is inserted on the nozzle and place a container holding a
minimum of 100 ml underneath (fig. 4).
5. “Hot water Press OK”: press the OK button (fig. 2). “Please
wait” is displayed and the appliance begins to deliver
water from the hot water spout.
The appliance ends the first start up procedure, then the
message “Turning off Please wait” is displayed and the
appliance goes off.
The coffee maker is now ready for normal use.
Please note:
• When using the appliance for the first time, you need to
make 4-5 cups of coffee or 4-5 cappuccinos before the
appliance starts to give satisfactory results.
TURNING THE APPlIANCE ON
Please note:
Before turning the appliance on, make sure the main switch on
the back of the appliance is in the i position (fig. 1).
each time the appliance is turned on, it performs an automatic
preheat and rinse cycle which cannot be interrupted.
The appliance is ready for use only after completion of this
cycle.
