background image

10

5.2  Installing the appliance

 Important! 

When you install the appliance, you should respect the follow-
ing safety warnings:

•  The appliance gives off heat. After positioning the appli-

ance on the worktop, leave a space of at least 3 cm be-

tween the surfaces of the appliance and the side and rear 

walls and at least 15 cm above the coffee maker.

•  Water penetrating the appliance could cause damage. Do 

not place the appliance near taps or sinks.

•  The appliance could be damaged if the water it contains 

freezes. Do not install the appliance in a room where the 

temperature could drop below freezing point.

•  Arrange the power cord (C8) in such a way that it cannot be 

damaged by sharp edges or contact with hot surfaces (e.g. 

electric hot plates).

5.3  Connecting the appliance

 Important! 

Check that the mains power supply voltage corresponds to that 
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly 
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance, 
have the socket replaced with a suitable type by a qualified 
electrician.

5.4  Setting up the appliance

 Please note:

•  Coffee has been used to factory test the appliance and it 

is therefore completely normal for there to be traces of 

coffee in the mill. The machine is, however, guaranteed to 

be new.

•  You should customise water hardness as soon as possible 

following the instructions in section “16. Setting water 

hardness”.

1.  Plug the power cord (C8) connector into the socket (A8) at 

the back of the appliance and connect the appliance to the 
mains electricity supply (fig. 1). Make sure the main switch 
(A7) at the back of the appliance is pressed (fig. 2);

2.  “Language”: press  (selection arrows 

 (B4) or 

 

(B5) until the required language is displayed between the 
two dotted lines, then press 

 (B3) to confirm.

Follow the instructions indicated on the appliance display (B1):
3.  “Fill tank”: remove the water tank (A18), fill to the MAX 

line (marked on the inside of the tank) with fresh water 
(fig. 3A), then reposition the tank (fig. 3B);

4.  “Insert water spout”: check that the hot water spout (C6) is 

attached to the nozzle (A15) (fig. 4) and place a container 
(fig. 5) underneath it with a minimum capacity of 100 ml;

5.  “Water circuit empty, Fill water circuit, Hot water, 

Confirm?”;

6.  Press 

 to confirm. The appliance delivers hot water 

from the spout then goes off automatically.

The coffee machine is now ready for normal use.

 Please note: 

•  When using for the first time, you need to make 4/5 cap-

puccinos before the appliance starts to give satisfactory 

results.

•  When using for the first time, the water circuit is empty, 

and the appliance may be very noisy: the noise will abate 

gradually as the circuit fills up.

•  When making the first 5-6 cappuccinos, it is normal to hear 

the noise of boiling water. After this, the noise becomes 

less.

•  To enjoy your coffee even more and improve the perfor-

mance of your appliance, we recommend installing a 

water softener filter (C4) as described in section “17. Water 

softener filter”. If your model is not supplied with this filter, 

you can order one from an authorised De’Longhi technical 

service centre.

6.  TURNING THE APPLIANCE ON

 Please note: 

Before turning the appliance on, make sure the main switch 
(A7) on the back of the appliance is pressed (fig. 2). 
Each time the appliance is turned on, it performs an automatic 
preheat and rinse cycle which cannot be interrupted. The appli-
ance is ready for use only after completion of this cycle.

 Danger of burns! 

During rinsing, a little hot water comes out of the coffee spouts 
(A14) and is collected in the drip tray (A24) underneath.  Avoid 
contact with splashes of water.

•  To turn the appliance on, press the 

 button (A12) 

(fig. 6). The message “Heating, Please wait” appears on the 

display (B1).

•  After heating, the message “Rinsing” is displayed, togeth-

er with a progress bar which gradually fills as preparation 

proceeds. As well as heating the boiler, the appliance also 

heats the internal circuits by circulating hot water. 

The appliance is at temperature when the message “Select your 
beverage” is displayed.

Summary of Contents for ECAM51X.55 series






























Reviews: