19
the openings at the side
for more than a minute
(fig. 34).
4. Extract the tank from the
appliance and fill with
water.
5. Insert the filter in the
water tank and immerse
it completely for about
ten minutes, sloping it to
enable the air bubbles to
escape (fig. 35).
6. Insert the filter in the fil-
ter housing and press as
far as it will go (fig. 36A)
7. Close the tank with the
lid, then put the tank
back in the machine (fig.
36B).
When you install the filter,
you must notify the appliance
of its presence.
8. Press the
MENU/ESC
button to enter the menu;
8. Press the
HOT MILK
or
LATTE
button (fig. 8) until “Install
filter” is displayed;
10. Press the
button;
11. The message “Enable?” is displayed.
12. Press the
button to confirm the selection. “Hot
water Confirm?” is displayed;
13. Position a container under the hot water spout (min. ca-
pacity: 500 ml);
14. Press the
button to confirm the selection. The
appliance begins hot water delivery and the message
“Please wait” is displayed;
15. After delivery, the appliance returns automatically to the
“Ready for coffee” position.
The new filter is active. You can now use the coffee maker.
Replacing the filter
When “REPLACE FILTER” is displayed, after two months (see
date indicator) or when the appliance has not been used for 3
weeks, you should replace the filter:
1. Extract the tank and exhausted filter;
2. Take the new filter out of its packet and proceed as
illustrated in points 2, 3, 4, 5 and 6 in the previous section.
3. Position a container with a minimum capacity of 500 ml
under the hot water spout.
4. Press the
MENU/ESC
button to enter the menu;
5. Press the
HOT MILK
or
LATTE
button until “Replace filter
“ is displayed.
6. Press the
button;
7. The message “Confirm?” is displayed.
8. Press the
button to confirm the selection;
9. “Hot water… Confirm?” is displayed.
10. Press the
button to confirm the selection. the
appliance begins delivering hot water and the message
“Please wait “ is displayed.
11. After delivery, the appliance returns automatically to the
“ready for coffee” position.
The new filter is now active and you can use the coffee maker.
Removing the filter
If you want to continue using the appliance without a filter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted filter;
2. Press the
MENU/ESC
button to enter the menu;
3. Press the
HOT MILK
or
LATTE
button (fig. 8) until “Install
filter Enabled” is displayed;
4. Press the
button
5. “Disable?” is displayed;
6. Press the
button to confirm and the
MENU/ESC
button to exit the menu.
TECHNICAL SPECIFICATION
Voltage:
220-240 V~ 50/60 Hz max. 10A
Absorbed power:
1450W
Pressure:
15 bar
Water tank capacity:
2.0 litres max.
Size Lxhxd:
238x350x445 mm
Cable length:
1.80 m
Weight:
11.8 kg
Beans container capacity:
250 g max.
The appliance complies with the following EC
directives:
• EC Regulation 1275/2008 for standby;
• Low Voltage Directive 2006/95/EC and subsequent
amendments;
• EMC directive 2004/108/EC and subsequent amendments
• Materials and accessories coming into contact with food
conform to eec regulation 1935/2004.
DISPOSAL
In compliance with European directive 2002/96/EC,
the appliance must not be disposed of with hou-
sehold waste, but taken to an authorised waste se-
paration and recycling centre.
33
35
36A
36B
Summary of Contents for ECAM28.46X
