DeLonghi ECAM28.46X, Instructions For Use Manual

Page: 12 / 24

11
3. Press the button. “Disable?” is displayed (or “En-
able?” if the function has been disabled);
4. Press the button to disable (or enable) the func-
tion.
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coffee hot.
Energy Saving
Use this function to enable or disable energy saving mode.
When enabled, the function reduces energy consumption in
compliance with European regulations.
To disable (or enable) “energy saving” mode, proceed as
follows:
1. Press the
MENU/ESC button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Energy
saving” is displayed;
3. Press the button. “Disable?” is displayed (or “En-
able?” if the function has been disabled);
4. Press the button to disable (or enable) energy
saving mode;
5. Then press the MENU/ESC button to exit the menu.
When the function is enabled, if the machine is not used for
about 1 minute, “Energy Saving” is displayed.
Please note!
• When in energy saving mode, a few seconds elapse
before the first coffee, cappuccino or milk based coffee is
delivered as the appliance must heat up again.
• To prepare any drink, press any button to exit energy
saving, then press the button corresponding to the drink
you want to make.
• If the milk container is inserted, “Energy saving” is not
activated.
Setting the temperature
To modify the temperature of the water used to make the cof-
fee, proceed as follows:
1. Press the
MENU/ESC
button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Set
temperature” is displayed;
3. Press the button;
4. Press the HOT MILK or LATTE button until the required
temperature (
●
= low;
●●●●
= high) is displayed;
5. Press the button to confirm;
6. Press the
MENU/ESC
button to exit the menu.
Setting water hardness
For instructions on setting water hardness, see page 20.
Beep
This enables or disables the beep emitted by the machine
each time the buttons are pressed or an accessory is inserted/
removed. The beep is enabled by default.
To disable or re-enable the beep, proceed as follows:
1. Press the
MENU/ESC
button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Beep”
is displayed;
3. Press the button. “ Disable?” or “ Enable?” is dis-
played;
4. Press the button to enable or disable the beep;
5. Press the MENU/ESC button to exit the menu.
Setting the language
To change the language for the display, proceed as follows:
1. Press the
MENU/ESC button to enter the menu;
2. Press the
HOT MILK
or
LATTE
button (fig. 8) until “Set
language” is displayed;
3. Press the button;
4. Press the HOT MILK or LATTE button until the required
language is displayed;
5. Press the button to confirm;
6. A message confirming the language installed is displayed;
7. Then press the MENU/ESC button to exit the menu.
Cup lighting
This function enables or disables the cup lighting. The lighting
is enabled by default.
The lights come on each time coffee and drinks with milk are
made and during each rinse cycle.
To disable or re-enable this function, proceed as follows:
1. Press the
MENU/ESC
button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “Cup
lighting” is displayed.
3. Press the button. “ Disable?” or “ Enable?” is dis-
played;
4. Press the button to enable or disable the cup
lighting;
5. Press the
MENU/ESC
button to exit the menu.
Default values (reset)
This resets all menu settings and programmed quantities back
to the default values (with the exception of the language
which remains as previously set).
To reset the default values, proceed as follows:
1. Press the
MENU/ESC
button to enter the menu;
2. Press the HOT MILK or LATTE button (fig. 8) until “De-
fault values” is displayed;
3. Press the button;
4. The message “Confirm?” is displayed.