39
EN
Make sure there are no pipes or electric wires in
the wall which could be damaged while mounting
the appliance.
3.1 WALL MOUNTING
Make sure the screws and anchors included in the
mounting pack are suitable for the type of wall on
which you are mounting the appliance. If in doubt,
contact a quali
fi
ed professional or your local dealer.
During installation, make sure the power cable is
disconnected from the power line.
The mounting kit includes:
A
- 2 x top mounts, 85 mm long
A
- 2 bottom mounts, 53 mm long
B
- 2 top brackets, 85 mm long
C
- 2 inner spacers
D
- 2 outer spacers
E
- 2 screw caps
F1
- 60 mm screws
F2
- 12 mm screws
F3
- 35 mm screws
G
- 4 x anchors
3.2 ELECTRICAL CONNECTIONS
You are recommended to have the appliance ins-
talled by a quali
fi
ed professional.
The appliance must be installed in compliance
with national legislation regulating electrical equi-
pment and installations.
When the appliance is installed, make the power is
off and the mains switch is in the “O“ position.
The appliance requires a 230 V ~ 50 Hz power supply.
Make sure the power line is appropriate for the data
given in table 1.
Never install the appliance:
- immediately below or in front of a power socket or
a junction box (Fig. 7)
- in contact with the wall or
fl
oor
- near curtains,
fl
ammable or combustible materials
or pressure vessels.
other control devices must always be in zone 3.
The appliance must not be connected with a plug.
WARNING:
Respect the distances shown in
fi
gures 4, 5.
To avoid all risks for young children, install the
appliance with the lowest heating element at least
600 mm from the
fl
oor. (Fig. 5).
IMPORTANT:
The radiator must be fastened to the wall and ad-
justed so that the fan heater is against the wall as
shown in
fi
gure 6.
Do not adjust the radiator in such a way that a
towel can be inserted between the wall and the
fi
lter. This could obstruct the air intake, causing
the fan heater to overheat and the “FILTER” light
to come on.
Radiator
elements
Radiator
elements
MOUNTING TEMPLATE
The mounting template (Fig. 8) can be found on the back of
the packaging and respects measurements A and B in table 1.
Open up the box completely and rest it against the wall and
the
fl
oor.
The minimum recommended distance between the bottom
holes and the
fl
oor is 645 mm.
With a pencil, mark the four holes on the wall, drill and insert
the anchors (G).
With the 60 mm screws (F1),
fi
x to the wall the two 85 mm
long top mounts (A) with the hole facing upwards and the
two 53 mm long bottom mounts (A) with the hole facing
downwards.
Fix the top part of the towel warmer, inserting it between
the inner spacer (C) and the outer spacer (D), making sure
that the deepest part of the inner spacer (C) is facing to-
wards the inside of the radiator and the “sx” symbol on the
outer spacer (D) is facing outwards.
Then screw the entire assembly to the bracket without ti-
ghtening fully. Insert the bracket (B) onto the mounts (A)
and fasten it using the 12 mm screws (F2). Fully tighten the
35 mm screw (F3) to
fi
x the top of the towel warmer and co-
ver it with the screw cap (E) provided. The appliance is now
mounted on the wall. Check that the minimum distance of
11 cm from the wall (
fi
g. 5) is respected for the full height of
the appliance.
