manualshive.com logo in svg

Dell XPS 730, Service Manual

Share
Download
Dell XPS 730 Service Manual Download Page 37

Replacing a PCI/PCI Express Card

35

Replacing the PCI and PCI Express Cards

 

CAUTION: 

To avoid electrostatic discharge and damage to internal components, 

ground yourself by using a wrist grounding strap or by periodically touching an 
unpainted metal surface on the computer chassis.

 

CAUTION: 

If your computer came with a PCI graphics card installed, removal of 

the card is not necessary when installing additional graphics cards; however, the 
card is required for troubleshooting purposes. If you remove the card, store it in a 
safe and secure location.

1

Follow the procedures in "Before You Begin" on page 13.

2

Remove the computer cover (see "Replacing the Computer Cover" on 

page 17).

3

Disconnect any cables connected to the card.

4

If the card is a full length, remove the captive screws on top of the PCI 

card fan shroud and remove the shroud.

5

Remove the card retention screw.

Summary of Contents for XPS 730















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands