manualshive.com logo in svg

Dell XPS 730, Service Manual

Share
Download
Dell XPS 730 Service Manual Download Page 32

30

Replacing a PCI/PCI Express Card

7

Press the securing tab (if present) on the system board connector as you 

grasp the card by its top corners, and then ease the card straight out of the 

connector.

8

Install a filler bracket in the empty card-slot opening. If you are replacing 

the card, see "Installing Graphics Cards for Multi Graphics Card" on 

page 31.

 

NOTE: 

Installing filler brackets over empty card-slot openings is necessary to 

maintain FCC certification of the computer. The brackets also keep dust and 

dirt out of your computer.

 

NOTE: 

The graphics card bridge (not present in all multi-graphics 

configurations) is not necessary in a single graphics card configuration.

 

CAUTION: 

Do not route card cables over or behind the cards. Cables routed over 

the cards can prevent the computer cover from closing properly or cause damage 
to the equipment.

9

Replace the PCI card fan shroud, replace the computer cover (see 

"Replacing the Computer Cover" on page 17), reconnect the computer 

and devices to electrical outlets, and then turn them on.

1

PCIe x16 card

2

securing tab

3

PCIe x16 card slot

1

3

2

Summary of Contents for XPS 730















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands