Dell XPS 730 Service Manual Download Page 102

Page: 102 / 110

102

System Setup

CPU Configuration

XD Bit

Capability

Enable XD Bit Capability to allow the processor to distinguish

between the bits of code that should be executed and the ones

that cannot be executed.

C1E Support

The Enhanced Halt State (C1E) reduces the processor speed

down to its lowest multiplier when the load on the processor is

reduced.

Max CPUID

Value Limit

Limits the max value the processor standard CPUID function

will support.

Intel(R)

Speedstep (tm)

tech

If enabled, the processor clock speed and core voltage are

adjusted dynamically based on the processor load.

Integrated Devices

USB Functions

Allows you to enable or disable the integrated USB controller.

HD Audio

Controller

Allows you to enable or disable the integrated audio controller.

Onboard

IEEE1394

Controller

Allows you to enable or disable the onboard IEEE1394

controller.

LAN1 BCM5784

Device

Allows you to enable or disable the onboard network controller.

LAN1 Option

ROM

Allows you to enable or disable the network controllers boot

option.

LAN2 BCM5784

Device

Allows you to enable or disable the onboard network controller.

LAN2 Option

ROM

Allows you to enable or disable the network controllers boot

option.

Configure

SATA#1-6 as

Allows you to configure the operating mode of the integrated

hard drive controller.

AHCI CD/DVD

Boot TIme out

Allows you to set the wait time for SATA CD/DVD in AHCI

mode.

Summary of Contents for XPS 730















































































































Search results

Summary of Contents for XPS 730

Reviews:

Brands by name

Popular brands

Dell XPS 730, Service Manual

Search results

Summary of Contents for XPS 730

Reviews:

Brands by name

Popular brands