background image

Next steps

1

Replace the 

SD memory card

2

Follow the procedure in 

after working inside your computer

Battery

Lithium-ion battery precautions

CAUTION: 

Exercise caution when handling Lithium-ion batteries.

Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting the AC adapter 

from the system to allow the battery to drain.

Do not crush, drop, mutilate, or penetrate the battery with foreign objects.

Do not expose the battery to high temperatures, or disassemble battery packs and cells.

Do not apply pressure to the surface of the battery.

Do not bend the battery.

Do not use tools of any kind to pry on or against the battery.

If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a Lithium-ion 

battery can be dangerous. In such an instance, the entire system should be replaced. Contac

https://www.dell.com/support

 for 

assistance and further instructions.

Always purchase genuine batteries from 

https://www.dell.com

 or authorized Dell partners and re-sellers.

Removing and installing components

19

Summary of Contents for Vostro 3400
















































































































Reviews: