Dell Studio 1557 Service Manual Download Page 34

Page: 34 / 49

Replacing the Mini-Card

Follow the instructions in

Remove the new Mini-Card from its packaging.

Insert the Mini-Card connector at a 45-degree angle into the appropriate system board connector. For example, the WLAN card connector is labeled

WLAN

and so on.

Press the other end of the Mini-Card down into the slot.

Replace the screw that secures the Mini-Card to the system board.

Connect the appropriate antenna cables to the Mini-Card you are installing. The following table provides the antenna cable color scheme for each Mini-
Card supported by your computer.

Secure the unused antenna cables in the protective mylar sleeve.

Replace the base cover (see

Replacing the Base Cover

Slide the battery into the battery bay until it clicks into place.

10.

Install the drivers and utilities for your computer, as required. For more information, see the

Dell Technology Guide

Back to Contents Page

CAUTION:

Install the UWB Mini-Card in the WWAN or WPAN slot. Do not install a UWB Mini-Card in the WLAN card slot. Doing so may cause

damage to your computer.

CAUTION:

Use firm and even pressure to slide the card into place. If you use excessive force, you may damage the connector.

Connectors on the Mini-Card

Antenna Cable Color Scheme

WWAN (2 antenna cables)

Main WWAN (white triangle)

Auxiliary WWAN (black triangle)

white with gray stripe

black with gray stripe

WLAN (2 or 3 antenna cables)

Main WLAN (white triangle)

Auxiliary WLAN (black triangle)

MIMO WLAN (*gray triangle)

white

black

gray

* The MIMO WLAN is optional and may not be available in all computers.

NOTE:

The gray antenna cable may not be available in all computers. The availability of the gray antenna cable in the Mini-Card compartment depends

on the type of display.

Summary of Contents for Studio 1557


















































Search results

Summary of Contents for Studio 1557

Reviews:

Related manuals for Studio 1557

Brands by name

Popular brands

Dell Studio 1557, Service Manual

Search results

Summary of Contents for Studio 1557

Reviews:

Related manuals for Studio 1557

Brands by name

Popular brands