manualshive.com logo in svg

Dell Studio 1435, Service Manual, Page: 32 / 41

Share
Download
Dell Studio 1435 Service Manual Download Page 32

 

  

5.

Lift the Mini-Card out of the system board connector.  
 

 

  

 

Replacing the Mini-Card  

 

 

1.

Remove the new Mini-Card from its packaging.  
 

 

 

2.

Insert the Mini-Card connector at a 45-degree angle into the appropriate system board connector. For example, the WLAN card connector is labeled 

WLAN

 and so on.  

 

 

  

3.

Press the other end of the Mini-Card down into the slot on the system board.  
 

 

  

4.

Replace the securing screw.  
 

 

  

5.

Connect the appropriate antenna cables to the Mini-Card you are installing. The following table provides the antenna cable color scheme for each Mini-
Card supported by your computer.  
 

 

 

6.

Secure the unused antenna cables in the protective mylar sleeve.  
 

 

  

7.

Replace the base cover (see 

Replacing the Base Cover

).  

 

 

  

8.

Slide the battery into the bay until it clicks into place.  
 

 

  

9.

Install the drivers and utilities for your computer, as required. For more information, see the 

Dell Technology Guide

.  

 

Back to Contents Page

 

 

 

 

NOTICE: 

When the Mini-Card is not in the computer, store it in protective antistatic packaging. For more information, see "Protecting Against 

Electrostatic Discharge" in the safety information that shipped with your computer.

 

NOTICE: 

Use firm and even pressure to slide the card into place. If you use excessive force, you may damage the connector.

Connectors on the Mini-Card  Antenna Cable Color Scheme 

WLAN (3 antenna cables)

 

Main WLAN (white triangle) 

Auxiliary WLAN (black triangle) 

MIMO WLAN (gray triangle) 

 

 

white 

black 

gray 

WPAN (one antenna cable)

 

WPAN 

 

 

blue 

 

NOTE: 

If you are installing a Mini-Card from a source other than Dell, you must install the appropriate drivers and utilities. For more generic driver 

information, see the 

Dell Technology Guide

.

Summary of Contents for Studio 1435










































Reviews:

No comments