background image

  5. Trouble Shooting Instructions

Common problems

The following table contains general information about common monitor problems you 
might encounter and the possible solutions:

Common 
Symptoms

What You 
Experience

Possible Solutions

No Video/
Power LED off

No picture

• Ensure that the video cable connecting the 

monitor and the computer is properly connected 
and secure.

• Verify that the power outlet is functioning 

properly using any other electrical equipment.

• Ensure that the power button is depressed fully.
• Ensure that the correct input source is selected 

in the 

Input Source

 menu.

No Video/
Power LED on

No picture or no 
brightness

• Increase brightness and contrast controls via 

OSD.

• Perform monitor self-test feature check.
• Check for bent or broken pins in the video cable 

connector.

• Run the built-in diagnostics.
• Ensure that the correct input source is selected 

in the 

Input Source

 menu.

Missing Pixels

LCD screen has 
spots

• Cycle power on-off.
• Pixel that is permanently off is a natural defect    

that can occur in LCD technology.

• For more information on Dell Monitor Quality   

and Pixel Policy, see Dell Support site at: 

https://www.dell.com/pixelguidelines

.

Stuck-on Pixels LCD screen has 

bright spots

• Cycle power On-Off.
• Pixel that is permanently off is a natural defect    

that can occur in LCD technology.

• For more information on Dell Monitor Quality    

and PixelPolicy, see Dell Support site at: 

https://www.dell.com/pixelguidelines

.

Brightness 
Problems

Picture too dim 
or too bright

• Reset the monitor to factory settings.
• Adjust brightness and contrast controls via OSD.

Summary of Contents for S2722DGM
















Reviews: