manualshive.com logo in svg

Dell Qlogic QME8242, User Manual, Page: 115 / 178

Share
Download
Dell Qlogic QME8242 User Manual Download Page 115

3–Adapter Management Applications

Windows Management Applications

CU0354602-00  A

3-55

Loopback Test

The loopback test is a diagnostic tool that routes transmit data through a loopback 
connector back to the same adapter.

Link Test

The link test inspects the link status (up or down) by checking the physical 
communication channel between the host and the firmware.

Windows Diagnostic Test Messages

If a test fails, an appropriate error code is generated and displayed, as shown in 

Table 3-9

. Note that this table does not list error messages for the Interrupt and 

Link tests.

Table 3-9. Windows Diagnostic Test Messages

Test

Error Message

Description 

Loopback LB_TEST_OK

Loopback test has passed

Loopback LB_SEND_WAIT_QUEUE_ERR

Send queue blocked

Loopback LB_NORCV_ERR

Receive packet not received

Loopback LB_NOMEM_ERR

No memory error

Loopback LB_TX_QUEUE_ERR

Transmit queue error

Loopback LB_SHORT_DATA_ERR

Looped data short error

Loopback LB_SEQUENCE_ERR

Looped data out of sequence

Loopback LB_DATA_ERR

Looped data corrupted

Loopback LB_ERR_CNT

Looped error count

Register

CR_TEST_OK

Control register test passed

Register

CR_NIU_MODE

Network interface unit (NIU) error

Register

CR_PHY

Physical layer (PHY) error 

Register

CR_ERRCNT

Control register error count

Hardware HW_TEST_OK

Hardware test has passed

Hardware HW_DMA_BZ_0

DMA channel 0 is busy

Hardware HW_DMA_BZ_1

DMA channel 1 is busy

Hardware HW_DMA_BZ_2

DMA channel 2 is busy

Hardware HW_DMA_BZ_3

DMA channel 3 is busy

Hardware HW_SRE_PBI_HALT

Segmentation and Reassembly Engine currently halted

Summary of Contents for Qlogic QME8242



















































































































































































Reviews:

No comments