Dell OptiPlex 580 Service Manual Download

Page: 45 / 54

Serial ATA:

Mini

–

tower

four 7-pin connectors

Desktop

three 7-pin connectors

Small form factor

three 7-pin connectors

Memory

four 240-pin connectors

Internal USB device

none

Processor fan

one 5

–

pin connector

Hard-drive fan:

Mini

–

tower

none

Desktop

none

Small form factor

one 5

–

pin connector

Front panel control

one 40

–

pin connector

Processor

AM3 941

–

pin connector

Power 12V

one 4

–

pin connector

Power

one 24

–

pin connector

PS/2 or serial connector (optional)

one 24

–

pin connector

Controls and Lights

Front of the computer:

Power button light

green light

—

Solid green light indicates power-on

state; blinking green light indicates sleep state of the
computer

amber light

—

Solid amber light when the computer

does not start indicates a problem with the system
board or power supply. Blinking amber light indicates
a problem with the system board

Power button

front of chassis

—

push button

Drive activity light

displays the SATA hard drive or optical drive activity

green light

—

blinking green light indicates that the

computer is reading data from, or writing data to,
from the drive

Network connectivity light

green light

—

a good connection exists between the

network and the computer

off (no light)

—

the computer is not detecting a

physical connection to the network

Diagnostic lights

four lights located on the front/back panel of the
computer. For information on the diagnostic lights,
see the

Service Manual

available on the Dell Support

website at

support.dell.com/manuals

Back of the computer:

Link integrity light on integrated network adapter green light

—

Link 10 Mbps

orange light

—

Link 100 Mbps

Network activity light on integrated network
adapter

yellow light

Power

DC power supply

Wattage:

EPA

Non-EPA

Mini

–

tower

255 W

305 W

Desktop

255 W

Small form factor

235 W

Maximum heat dissipation:

Mini

–

tower

1041 BTU/hr.

Desktop

955 BTU/hr.

Small form factor

938 BTU/hr.

Voltage:

Mini

–

tower

115/230 VAC, 50/60 Hz, 3.6/1.8 A

115/230 VAC, 50/60 Hz, 3.6/1.8
A

Desktop

115/230 VAC, 50/60 Hz, 4.0/2.0 A

115/230 VAC, 50/60 Hz, 4.0/2.0
A

Small form factor

115/230 VAC, 50/60 Hz, 3.5/1.8 A

115/230 VAC, 50/60 Hz, 3.5/1.8
A

Coin

–

cell battery

3 V CR2032 lithium coin cell

Summary of Contents for OptiPlex 580























































Search results

Summary of Contents for OptiPlex 580

Reviews:

Related manuals for OptiPlex 580

Brands by name

Popular brands

Dell OptiPlex 580, Service Manual

Search results

Summary of Contents for OptiPlex 580

Reviews:

Related manuals for OptiPlex 580

Brands by name

Popular brands