Dell MD1400-16TB Setup Manual Download Page 33

Page: 33 / 43

PowerVault (Dell MD1400 - 16TB) Setup Guide

3. Connect the other end of the SAS cables to the External Storage units. See

a. Connect the

Primary

Port 1 of the first PowerVault to Port 0 of the PERC Card on the

left using a cable with square

Mini-SAS (Codename SFF-8088)

to square

Mini-SAS

(Codename SFF-8088)

connectors.

b. Daisy chain up to three additional PowerVaults to the first PowerVault using cables with

square

Mini-SAS (Codename SFF-8088)

to square

Mini-SAS (Codename SFF-8088)

connectors.

c. Connect the

Primary

Port 1 of the first 15-Drive DAC to Port 0 of the PERC Card on

the right using a cable with rectangular

Mini-SAS HD (Codename SFF-8614)

to square

Mini-SAS (Codename SFF-8088

connectors.

d. Daisy chain up to three additional 15-Drive DACs to the first 15-Drive DAC using cables

with rectangular

Mini-SAS HD (Codename SFF-8614)

to rectangular

Mini-SAS HD

(Codename SFF-8614)

connectors.

The following figure shows an NetWitness Series 5 (R630) host connected to four
PowerVaults and four 15-Drive DACs.

Install PowerVaults and 15-Drive DACs on a Series 5 or Series 6 Host (Mixed

Mode)

Summary of Contents for MD1400-16TB












































Search results

Summary of Contents for MD1400-16TB

Reviews:

Related manuals for MD1400-16TB

Brands by name

Popular brands

Dell MD1400-16TB, Setup Manual

Search results

Summary of Contents for MD1400-16TB

Reviews:

Related manuals for MD1400-16TB

Brands by name

Popular brands