Dell Latitude 3000 Series Service Manual Download

Page: 46 / 79

Replacing the heat sink

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/

regulatory_compliance.

CAUTION:

Incorrect alignment of the heat sink can damage the system board and processor.

NOTE:

The original thermal grease can be reused if the original system board and heat sink are reinstalled together. If either

the system board or the heat sink is replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is
achieved.

Topics:

•

Procedure

•

Post-requisites

Procedure

1. Slide the heat sink below the tab on the display hinge and place it on the system board.
2. Align the screws on the heat sink with the screw holes on the system board.
3. Replace the screws that secure the heat sink to the system board.

Post-requisites

1. Follow the procedure from step 3 to step 7 in “

Replacing the base cover

”.

2. Replace the

keyboard

3. Follow the procedures from step 4 to step 5 in “

Replacing the optical drive

”.

4. Replace the

battery

Replacing the heat sink

Summary of Contents for Latitude 3000 Series
















































































Search results

Summary of Contents for Latitude 3000 Series

Reviews:

Related manuals for Latitude 3000 Series

Brands by name

Popular brands

Dell Latitude 3000 Series, Service Manual

Search results

Summary of Contents for Latitude 3000 Series

Reviews:

Related manuals for Latitude 3000 Series

Brands by name

Popular brands