manualshive.com logo in svg

Dell Inspiron 2100, Service Manual, Page: 33 / 73

Share
Download
Dell Inspiron 2100 Service Manual Download Page 33

1-16

Dell PowerEdge 2100/180 and 2100/200 Systems Service Manual

Table 1-2.  Jumper Descriptions  

Jumper

Description

Settings

200MHZ

Microprocessor speed

Installed if the micro-
processor’s internal speed is 
200 MHz, otherwise, not 
installed.

180MHZ

Microprocessor speed

Installed if the micro-
processor’s internal speed is 
180 MHz, otherwise, not 
installed.

PASSWD

Password enable/disable

Jumper installed to activate 
boot password feature.

EISA

Clear EISA configuration 
settings

Install the jumper and boot 
the system to clear the con-
figuration settings.

Remove the jumper and use 
the EISA Configuration Util-
ity to configure the system.

VGA

Integrated VGA controller 
enable/disable

Install to enable the inte-
grated VGA controller.

CARDBIOS

Used for trouble shooting

Install the jumper to boot 
system from BIOS expan-
sion card. 

Remove the jumper to allow 
normal boot operation from 
BIOS.

Summary of Contents for Inspiron 2100










































































Reviews:

No comments