Dell Inspiron 2100 Service Manual Download Page 31

Page: 31 / 73

1-14

Dell PowerEdge 2100/180 and 2100/200 Systems Service Manual

System Board Layout

The subsections that follow provide service-related information about the sys-
tem board components.

Figure 1-11. System Board Components

keyboard (bottom) and
mouse (top) connec-
tors (KYBD/MOUSE)

video connector
(JVGA)

parallel port connector
(PARALLEL)

serial port 1 (bottom)
and serial port 2 (top)
connectors (SERIAL)

diskette/tape drive interface
connector (FLOPPY)

control-panel connector
(PANEL)

battery socket
(BATTERY)

top of the computer

microprocessor socket

EISA connectors (EISA1
[lower], EISA2, and EISA3)

fan connector (FAN)

power connector (POWER)

3-volt power connector
(POWER3V)

auxiliary fan connector
(AUXFAN)

DIMM connectors (DIMM_A
[lower], DIMM_B, DIMM_C,
and DIMM_D)

PCI connectors (PCI4
[lower], PCI5, and
PCI6)

server management
connector (SRV_MGT)

integrated SCSI port
connector (SCSI)

Summary of Contents for Inspiron 2100










































































Search results

Summary of Contents for Inspiron 2100

Reviews:

Related manuals for Inspiron 2100

Brands by name

Popular brands

Dell Inspiron 2100, Service Manual

Search results

Summary of Contents for Inspiron 2100

Reviews:

Related manuals for Inspiron 2100

Brands by name

Popular brands