manualshive.com logo in svg

Dell Inspiron 13 7000 2-in-1, Service Manual

Share
Download
Dell Inspiron 13 7000 2-in-1 Service Manual Download Page 62

Removing the heat sink

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before working inside your computer

. After working inside your 

computer, follow the instructions in 

After working inside your 

computer

. For more safety best practices, see the Regulatory 

Compliance home page at 

www.dell.com/regulatory_compliance

.

WARNING: The heat sink may become hot during normal operation. 
Allow sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the 

heat transfer areas on the heat sink. The oils in your skin can reduce 

the heat transfer capability of the thermal grease.

 

Prerequisites

1 

Remove the 

base cover

.

2 

Remove the 

battery

.

Procedure

1 

In sequential order (as indicated on the heat sink), loosen the captive 

screws that secure the heat sink to the system board.

62

Summary of Contents for Inspiron 13 7000 2-in-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands