manualshive.com logo in svg

Dell Inspiron 13 7000 2-in-1, Service Manual

Share
Download
Dell Inspiron 13 7000 2-in-1 Service Manual Download Page 126

Changing the display settings in Intel HD Graphics 

Control Panel

1 

Right-click or touch and hold on the desktop and select 

Graphics 

Properties

 to launch the 

Intel HD Graphics Control Panel

.

2 

Click or tap 

Display

.

3 

Change the display settings as required.

Intel WiDi

The wireless display feature allows you to share your computer display with a 
compatible TV without using cables. You must connect a wireless display 
adapter to your TV before setting up the wireless display. To check if your TV 
supports this feature, see the documentation that is shipped with the TV.
The following table provides the basic system requirements for a wireless 
display.

Processor

2nd generation Intel Core i5, i7

Video 

controller

Intel HD Graphics

WLAN card

Intel 2230 or Intel 6150

126

Summary of Contents for Inspiron 13 7000 2-in-1


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands