Dell G7 7700 Service Manual Download Page 59

Page: 59 / 96

Removing the power button with fingerprint reader

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

NOTE:

The system board can be removed and installed along with the heat sink. This simplifies the removal and

installation procedure and prevents damage to the thermal bond between the system board and heat sink.

About this task

The following image indicates the location of the power button with fingerprint reader and provides a visual representation of the removal
procedure.

Steps

1. Lift the power button with fingerprint reader off the palm-rest and keyboard assembly.
2. Remove the two screws (M1.6x1.8) that secure the power-button bracket to the palm-rest and keyboard assembly.

Removing and installing components

Summary of Contents for G7 7700

































































































Search results

Summary of Contents for G7 7700

Reviews:

Related manuals for G7 7700

Brands by name

Popular brands

Dell G7 7700, Service Manual

Search results

Summary of Contents for G7 7700

Reviews:

Related manuals for G7 7700

Brands by name

Popular brands