Dell G7 7700 Service Manual Download Page 13

Page: 13 / 96

Steps

1. Remove the six screws (M2x5) that secure the base cover to the palm-rest and keyboard assembly.
2. Loosen the two captive screws that secure the base cover to the palm-rest and keyboard assembly.

CAUTION:

Do not pull on or pry the base cover at the side where the hinges are located; doing so may damage the

base cover.

NOTE:

Loosening the two captive screws on the base cover creates a gap which can be used to pry and lift the base

cover off the palm-rest and keyboard assembly.

3. Starting from the bottom-left corner, use a plastic scribe to pry the base cover and to release the base cover from the tabs. Lift the

base cover off the palm-rest and keyboard assembly.

NOTE:

The following steps are applicable only if you want to further remove any other component from your

computer.

4. Disconnect the battery cable from the system board.
5. Turn your computer over and press the power button for 15 seconds to drain the flea power.

Installing the base cover

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the base cover and provide a visual representation of the installation procedure.

Removing and installing components

Summary of Contents for G7 7700

































































































Search results

Summary of Contents for G7 7700

Reviews:

Related manuals for G7 7700

Brands by name

Popular brands

Dell G7 7700, Service Manual

Search results

Summary of Contents for G7 7700

Reviews:

Related manuals for G7 7700

Brands by name

Popular brands