Dell ECS EX Series Hardware Manual Download | Manualshive

Page: 18 / 112

background image

The front view of an EX500 rack with the minimum node configuration and an EX500 rack with the maximum node configuration
is shown in the following diagram. The rear view requires a brace wherever there is empty space above or below an EX500
server.

Figure 7. EX500 minimum and maximum configurations

The EX500 appliance is available in the following configurations within a Dell EMC rack or a customer-provided rack.

>

EX500 supports 5 nodes in the same configuration. You can combine 8 TB, 12 TB, and 16 TB disks, with a minimum of 5 nodes
containing the same disk configuration (size and quantity). 16 TB requires ECS 3.5 and later releases.

Table 6. EX500 configurations

Nodes

Disks in each node

Disk Size

RAW Storage capacity

5 (minimum configuration)

12

●

8 TB

●

12 TB

●

16 TB

●

480 TB

●

1.44 PB

●

1.92 PB

24

●

8 TB

●

12 TB

●

16 TB

●

960 TB

●

1.44 PB

●

1.92 PB

6

12

●

8 TB

●

12 TB

●

16 TB

●

576 TB

●

864 TB

●

1.15 PB

24

●

8 TB

●

12 TB

●

16 TB

●

1.15 PB

●

1.73 PB

●

2.30 PB

7

12

●

8 TB

●

12 TB

●

16 TB

●

672 TB

●

1.01 PB

●

1.34 PB

24

●

8 TB

●

12 TB

●

1.34 PB

●

2.02 PB

18

EX500 Platform

«
...
16
17
18
19
20
...
»

Summary of Contents for ECS EX Series

















































































































Reviews:

No comments

Related manuals for ECS EX Series

Univerge SV8100

Brand: NEC Pages: 78

Univerge SV8100

Brand: NEC Pages: 186

Univerge SV8100

Brand: NEC Pages: 150

Univerge SV8100

Brand: NEC Pages: 52

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: Bang & Olufsen Pages: 28

Modbus Server-FC330A

Brand: IntesisBox Pages: 5

Brand: IBM Pages: 194

Brand: BELINEA Pages: 53

imagePRESS Server G200

Brand: Canon Pages: 98

imagePRESS A3200

Brand: Canon Pages: 192

ColorPass-Z7400

Brand: Canon Pages: 210

ApplianceStor 90

Brand: Rasilient Pages: 42

Brand: ClearCube Pages: 2

Brand: Kystar Pages: 46

QuadView LES290A

Brand: RGB Spectrum Pages: 7

Brand: GIGA-BYTE TECHNOLOGY Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands