Dell E70S Installation And Service Manual Download Page 217

Page: 217 / 238

Remove the standard cooling fans

and install the

High performance (silver grade) fan or high-performance (gold grade) fan

cooling fans

NOTE:

Refer to the cooling fan and foam requirement matrix for the cooling fan and foam requirement for different

configurations.

Table 71. Cooling fan and foam requirement matrix

System

configuration

Cooling fan

Foam requirement

w/GPU

w/GPU + Barlow Pass

DIMM

w/GPU

w/GPU + Barlow Pass

DIMM

8 x 2.5-inch
NVMe

HPR SLVR

HPR GOLD

Yes

16 x 2.5-inch
SAS/SATA

HPR GOLD

Yes

16 x 2.5-inch
NVMe

HPR GOLD

Yes

24 x 2.5-inch
SAS/SATA

HPR GOLD

Yes

16 x 2.5-inch
SAS/SATA + 8 x
2.5-inch NVMe

HPR GOLD

Yes

HPR - High Performance, SLVR - Silver

NOTE:

For more information about supported cooling fans matrix, see the thermal restriction section in

Dell EMC

PowerEdge R750 Technical Specifications

on the product documentation page.

NOTE:

12 x 3.5 inch and rear drive configuration systems do not support GPU card.

Remove the heat sink

and

install the required t-type heat sink

NOTE:

All GPU cards require t-type heat sink and GPU shroud, irrespective of the length.

Remove the air shroud

and

install the GPU air shroud

Remove the GPU air shroud top cover

NOTE:

The GPU air shroud top cover is part of the GPU air shroud.

Remove the GPU air shroud filler

Install the GPU

NOTE:

See

expansion card installation guidelines

to know about risers and slots that support GPU.

NOTE:

For information on riser slot location on the system board, see the

System board jumpers and connectors

topic.

7. If applicable, connect the power cables to the GPU. To know the connectors for GPU on the system board, see the

System

board jumpers and connectors

topic.

Refer to the GPU power cable matrix to know about the requirement of cable for the GPU.

Table 72. GPU power cable matrix

Category

Description

Type

Vendor

Cable

Cable quantity

GPU

CRD,GRPHC,NVIDIA,
T4, 16 GB, 70 W, L

HH and HL (FH and
LP brackets)

NVIDIA

Not required

GPU

NVIDIA Volta Next
300 W DW GPU
(A100)-Gen 4

FH and FL

NVIDIA

8-pin cable

1 piece per GPU riser

GPU

Nvidia RTX-A40

FH and FL

NVIDIA

8-pin cable

1 piece per GPU riser

GPU

CRD,GRPHC,32 GB,
225 W, M10, PASSIV

FH and FL

NVIDIA

6 + 2-pin cable

1 piece per GPU riser

HH - Half Height, HL - Half Length, FH - Full Height, FL - Full Length

Upgrade Kits

217

Summary of Contents for E70S















































































































































































































































Search results

Summary of Contents for E70S

Reviews:

Related manuals for E70S

Brands by name

Popular brands

Dell E70S, Installation And Service Manual

Search results

Summary of Contents for E70S

Reviews:

Related manuals for E70S

Brands by name

Popular brands