Dell E70S Installation And Service Manual Download Page 212

Page: 212 / 238

Upgrade Kits

The table lists the available After Point Of Sale [APOS] kits.

Table 67. Upgrade kits

Kits

Related links to service instructions

Bezel

See

Installing the front bezel

Boss

See

Installing the M.2 SSD module

BOSS S2

See

Installing the BOSS S2 controller card module

Embedded management (IDSDM)

See

IDSDM kit

GPU

See

GPU kit

Accelerator enablement kit

See

GPU kit

Hard drives

See

Installing the drive

Hard drives SSD

See

Installing the drive into the carrier

Memory

See

Installing a memory module

Network cards (Standard PCIe adapter
LP/FH)

See

Installing the LOM card and rear I/O board

Network cards (OCP)

See

Installing the OCP card

PCIe SSD card

See

Installing the drive

Power cords

N/A

Power supplies

See

Installing a power supply unit

Quick sync

N/A

SD cards

See

Installing the MicroSD card

TPM

See

Upgrading the Trusted Platform Module

Processor enablement thermal kits

See

Installing the processor

Internal USB 3.0 card

See

Internal USB card kit

Serial COM port daughter card

See

Installing the serial COM port

VGA port for liquid cooling system

See

Installing the VGA port

Cables

N/A

Fans

See

Installing a fan

Heat sink

See

Installing a processor heat sink module

Risers

See

Installing the expansion riser

Rail

N/A

CMA

N/A

Topics:

•

BOSS S2 module kit

•

GPU kit

•

IDSDM kit

212

Upgrade Kits

Summary of Contents for E70S















































































































































































































































Search results

Summary of Contents for E70S

Reviews:

Related manuals for E70S

Brands by name

Popular brands

Dell E70S, Installation And Service Manual

Search results

Summary of Contents for E70S

Reviews:

Related manuals for E70S

Brands by name

Popular brands