manualshive.com logo in svg

Dell DF10MXL, Getting Started Manual

Share
Download
Dell DF10MXL Getting Started Manual Download Page 8

8

Hardware Overview

Hardware Overview

This section contains information about device characteristics and modular 

hardware configurations for the MXL 10/40GbE Switch.

Internal Ports

The MXL 10/40GbE Switch provides thirty-two 1/10-Gigabit Ethernet 

internal ports. The internal ports are connected to server blades through the 

M1000e chassis midplane. Each port can operate in either 1GbE or 10GbE 

mode. Internal ports are numbered 1 to 32.
The MXL 10/40GbE Switch also provides an internal Ethernet interface—the 

out-of-band (OOB) interface—which is dedicated to switch management. 

The OOB interface is connected to the chassis management controller 

(CMC) through the chassis midplane. Traffic on this port is segregated from 

operational network traffic on the switch ports and cannot be switched or 

routed to the operational network.

Front Panel

Figure 1-1 shows the MXL 10/40GbE Switch front panel:

Figure 1-1. MXL 10/40GbE Switch: Front Panel l

Expansion Slot 1

40GbE QSFP+ Ports

USB Console Port

Expansion Slot 0

Summary of Contents for DF10MXL





































Reviews:

No comments

Brands by name

Popular brands

Load more brands