manualshive.com logo in svg

Dell DF10MXL, Getting Started Manual

Share
Download
Dell DF10MXL Getting Started Manual Download Page 17

Installing and Configuring the Switch

17

Unpacking the Switch

Package Contents

When unpacking each switch, make sure that the following items are 

included:

• One Dell Networking MXL 10/40GbE Switch IO Module
• One USB type A-to-DB-9 female cable

• Getting Started Guide
• Safety and Regulatory Information
• Warranty and Support Information
• Software License Agreement

Unpacking Steps

NOTE: 

Before unpacking the switch, inspect the container and immediately report any 

evidence of damage.

1

Place the container on a clean, flat surface and cut all straps securing the 

container.

2

Open the container or remove the container top.

3

Carefully remove the switch from the container and place it on a secure 

and clean surface.

4

Remove all packing material.

5

Inspect the product and accessories for damage.

Installing and Configuring the 

Switch

After you unpack the MXL 10/40GbE Switch, refer to the flow chart in 

Figure 1-7 for an overview of the steps you must follow to install the blade 

and perform the initial configuration.

 

To see if a switch is running the latest Dell Networking OS version, use the show 

version command. To download an Dell Networking OS version, go to 

http://support.dell.com

.

Summary of Contents for DF10MXL





































Reviews:

No comments

Brands by name

Popular brands

Load more brands