manualshive.com logo in svg

Dell DF10MXL, Getting Started Manual

Share
Download
Dell DF10MXL Getting Started Manual Download Page 33

Next Steps

33

Next Steps

If you installed the MXL 10/40GbE Switch in a stack, you can configure 

additional settings for switch stacking.
For information about how to create different stacking scenarios, refer to the 

Ethernet Stacking

 white paper on the Dell Support and Dell Networking 

White Papers websites at: 

http://support.dell.com/manuals

http://en.community.dell.com/techcenter/networking/w/wiki/networking-

whitepapers.aspx

 

For information about how to configure stacking, refer to the 

Configuration 

Guide for the Dell Networking MXL 10/40 GbE Switch IO Module 

on the Dell 

Support website at 

http://support.dell.com/manuals

.

• You can customize the MXL 10/40GbE Switch for use in your data center 

network by configuring software features as necessary. To perform 

additional switch configuration, do one of the following:
• For remote out-of-band management, enter the OOB management 

interface IP address into a Telnet or SSH client and log in to the 

switch using the user ID and password to access the CLI. 

• For local management, use the attached console connection to log in 

to the CLI.

• For remote in-band management from a network management 

station, enter the IP address of the default virtual local area network 

(VLAN) and log in to the switch to access the CLI. 

For information about how to configure software settings, refer to the 

Configuration Guide for the Dell Networking MXL 10/40 GbE Switch IO 

Module 

on the Dell Support website at 

http://support.dell.com/manuals

.

Summary of Contents for DF10MXL





































Reviews:

No comments

Brands by name

Popular brands

Load more brands