Dell D03T Service Manual Download Page 97

Page: 97 / 119

Steps

1. Slide the front I/O-ports on the system board into the front I/O-slots on the chassis and align the screw holes on the

system board with the screw holes on the chassis.

2. Replace the eleven (#6-32) screws that secure the system board to the chassis.
3. Align and place the supporting bracket on the system board.
4. Install the two (M3) screws to secure the supporting bracket to the system board

Next steps

1. Install the

processor

2. Install the

power-supply unit

NOTE:

Install the power-supply cable clips to the power-supply cover replacing the system board.

3. Install the

and

4. Install the

5. Install the

6. Install the

NOTE:

Install the graphics-card rubber protector to the chassis after replacing the system board.

7. Install the

internal hard-drive cage

8. Install the

hard-drive fan assembly

9. Install the

10. Install the

11. Install the

12. Install the

13. Install the

14. Install the

15. Install the

16. Install the

17. Follow the procedure in

After working inside your computer

Removing and installing components

Summary of Contents for D03T
























































































































Search results

Summary of Contents for D03T

Reviews:

Related manuals for D03T

Brands by name

Popular brands

Dell D03T, Service Manual

Search results

Summary of Contents for D03T

Reviews:

Related manuals for D03T

Brands by name

Popular brands