Dell D03T Service Manual Download Page 60

Page: 60 / 119

Steps

1. Align the screws on the processor fan and heat-sink assembly with the screw holders on the system board and place the

processor fan and heat-sink assembly on the processor.

NOTE:

Ensure that the triangle mark is directed towards the rear side of the computer.

2. In the sequential order (1->2->3->4), tighten the captive screws to secure the processor fan and heat-sink assembly to the

system board.

NOTE:

Tighten the screws in a sequential order (1,2,3,4) as printed on the system board.

Next steps

1. Install the

air shroud

2. Install the

side cover

3. Follow the procedure in

After working inside your computer

Hard-drive fan assembly

Removing the hard-drive fan assembly

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

side cover

3. Remove the

air shroud

About this task

The following images indicate the location of the hard-drive fan assembly and provide a visual representation of the removal
procedure.

Removing and installing components

Summary of Contents for D03T
























































































































Search results

Summary of Contents for D03T

Reviews:

Related manuals for D03T

Brands by name

Popular brands

Dell D03T, Service Manual

Search results

Summary of Contents for D03T

Reviews:

Related manuals for D03T

Brands by name

Popular brands