background image

WARNING: 

Please carefully select the installation position and make sure that 

the final output power does not exceed the limits set forth in relevant rules. 
The violation of these rules could possibly lead to serious federal penalties.

Instructions d'installation professionnelles

Le personnel d'installation

Ce produit est conçu pour des applications spécifiques et doit être installé par un 
personnel qualifié avec RF et connaissances connexes réglementaire. L'utilisateur ne 
doit pas tenter générale d'installer ou de modifier le réglage.

Lieu d'installation

Le produit doit être installé à un endroit où l'antenne de rayonnement est 
maintenue à 20 cm de personnes à proximité dans son état de fonctionnement 
normal, afin de répondre aux exigences réglementaires d'exposition aux 
radiofréquences.

Antenne externe

Utilisez uniquement l'antenne(s) qui ont été approuvés par le demandeur. Antenne 
(s) peuvent produire de l'énergie RF parasite indésirable ou excessive transmission 
qui peut conduire à une violation des normes de la FCC / IC est interdite et non-
approuvé.

Procédure d'installation

ATTENTION: S'il vous plaît choisir avec soin la position d'installation et assurez-
vous que la puissance de sortie final ne dépasse pas les limites fixées dans les 
règles pertinentes. La violation de ces règles pourrait conduire à des sanctions 
fédérales graves.

Federal Communication Commission 

Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) This device may not cause harmful interference, and 
(2) this device must accept any interference received, including interference that 
may cause undesired operation.

Setting up your Dell Edge Gateway

12

Summary of Contents for 5000 Series


































































Reviews: