manualshive.com logo in svg

Dell EMC VNXe3100, Manual

Share
Download
Dell EMC VNXe3100 Manual Download Page 3

Tasks to add an SP

EMC VNXe3100/VNXe3150 — Adding a Second Storage Processor 

3

The SP fault LED will flash alternating amber and blue while the SP remains in Service 
mode and is receiving active power.

Task 2: Remove the cache protection module

To replace a cache protection module with a storage processor, you must completely 
power down your entire system, including any attached disk-array enclosures (DAEs).

DO NOT REMOVE a cache protection module while the “Unsafe to remove” LED is 
on. The light indicates that you may interrupt a vital system or data-caching 
process.

Wait until both “Unsafe to Remove” LEDs are off, then perform the following steps:

1. On the DPE and 

each

 DAE attached to the VNXe3100 or VNXe3150:

a. Release the cable retention bail and unplug the power cord from each power 

cooling/module.

b. Mark the cords “A” or “B” for the power/cooling modules from which you removed 

them.

2. Locate the two orange release levers on the cache protection module latches.

3. Squeeze the levers to release the latches and then pull the latches outward.

4. Pull out the latches until they are fully extended and the cache protection module is 

released from its enclosure.

1

1

1

1 GBE

0 1

X4

6Gb SAS
6Gb SAS

2

3

1
0

e3

e0 e1

e2

1 GbE

SP fault

CL4701

Summary of Contents for VNXe3100















Reviews:

No comments

Brands by name

Popular brands

Load more brands