manualshive.com logo in svg

Dell EMC PowerEdge MX5000s, Installation And Service Manual

Share
Download
Dell EMC PowerEdge MX5000s Installation And Service Manual Download Page 3

Chapter 1: About this document....................................................................................................... 5

Chapter 2: System overview............................................................................................................ 6

Dell EMC PowerEdge MX5016s sled overview................................................................................................................. 6

Inside the sled...................................................................................................................................................................6
Front view of the sled......................................................................................................................................................7
Locating the Service Tag of your system..................................................................................................................... 7
System information label.................................................................................................................................................8

Dell EMC PowerEdge MX5000s SAS IOM overview....................................................................................................... 8

Front view of PowerEdge MX5000s module...............................................................................................................9

Chapter 3: Initial system setup and configuration for MX5016s......................................................... 10

Setting up your system....................................................................................................................................................... 10
Storage sled mapping configurations................................................................................................................................. 11
Drive assignment...................................................................................................................................................................11

Chapter 4: Installing and removing system components ................................................................... 14

Safety instructions............................................................................................................................................................... 14
Recommended tools............................................................................................................................................................ 14
Storage sled.......................................................................................................................................................................... 15

Removing the sled from the enclosure........................................................................................................................15
Installing the sled into the enclosure............................................................................................................................16

Drive drawer..........................................................................................................................................................................17

Opening the drive drawer..............................................................................................................................................17
Closing the drive drawer................................................................................................................................................18

Drives.................................................................................................................................................................................... 20

Removing a drive blank.................................................................................................................................................20
Installing a drive blank.................................................................................................................................................... 21
Removing a drive carrier...............................................................................................................................................22
Installing a drive carrier................................................................................................................................................. 23
Removing a drive from the drive carrier.....................................................................................................................24
Installing a drive into the drive carrier......................................................................................................................... 25

Storage expander module.................................................................................................................................................. 25

Removing an expander module....................................................................................................................................26
Installing an expander module...................................................................................................................................... 27

SAS IOM module..................................................................................................................................................................27

Removing a MX5016s blank from Fabric C slot.........................................................................................................27
Installing a MX5016s blank in Fabric C slot................................................................................................................ 28
Removing a MX5016s module from Fabric C slot..................................................................................................... 29
Installing a MX5016s module into Fabric C slot......................................................................................................... 30

Chapter 5: Technical specifications................................................................................................ 32

Sled dimensions................................................................................................................................................................... 32
Sled weight...........................................................................................................................................................................32

Contents

Contents

3

Summary of Contents for PowerEdge MX5000s












































Reviews:

No comments

Brands by name

Popular brands

Load more brands