Dell EMC PowerEdge MX5000s Installation And Service Manual Download Page 29 | Manualshive

Page: 29 / 43

background image

Figure 23. Installing a blank in Fabric C slot

Removing a MX5016s module from Fabric C slot

Prerequisites

NOTE:

MX5016s storage sled does not support single SAS IOM configuration.

1. Follow the safety guidelines listed in

Safety instructions

.

2. If applicable, disconnect the cables that are connected to the modules.

Steps

1. Press the orange release button on the module to open the release lever.
2. Hold the release lever, and pull the I/O module out of the enclosure.

NOTE:

Ensure that you install MX5016s blank if you are removing a module permanently.

Installing and removing system components

29

«
...
27
28
29
30
31
...
»

Summary of Contents for PowerEdge MX5000s












































Reviews:

No comments

Related manuals for PowerEdge MX5000s

Brand: National Instruments Pages: 34

Lucent Technologies Stinger MS+

Brand: BELL LABS INNOVATIONS Pages: 100

Brand: National Instruments Pages: 9

TEG-S3000I - TEG Gigabit Layer 2 Managed Chassis S3000i Switch

Brand: TRENDnet Pages: 11

Brand: Multitech Pages: 50

Brand: Digiop Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands