manualshive.com logo in svg

Dell EMC PowerEdge MX5000s, Installation And Service Manual

Share
Download
Dell EMC PowerEdge MX5000s Installation And Service Manual Download Page 6

System overview

Topics:

•

Dell EMC PowerEdge MX5016s sled overview

•

Dell EMC PowerEdge MX5000s SAS IOM overview

Dell EMC PowerEdge MX5016s sled overview

The PowerEdge MX5016s is a Storage Sled installed in the PowerEdge MX7000 enclosure to provide disk expansion for PowerEdge MX
series Compute Sleds. In the PowerEdge MX7000 enclosure, the PowerEdge MX5016s is connected through an internal SAS fabric (Fab-
C). The PowerEdge MX5000s provides flexible SAS connectivity between compute sleds, and internal storage sleds connected to the
MX7000 enclosure.

PowerEdge MX5016s supports up to:

•

16 hot-swappable 2.5-inch SAS drives

•

Two hot-swappable expanders providing dual SAS paths for all drives(HDDs/SSDs)

•

Dual x4 SAS links to the MX platform infrastructure

•

12 GB/s SAS support

NOTE:

 All instances of SAS hard drives and SSDs are referred to as drives in this document, unless specified otherwise.

Inside the sled

Figure 1. Inside the MX5016s sled

1. Slide rail

2. Expander modules

3. Drives

4. Sled cover

2

6

System overview

Summary of Contents for PowerEdge MX5000s












































Reviews:

No comments

Brands by name

Popular brands

Load more brands