Dell EMC E68S Installation And Service Manual Download | Manualshive

Page: 53 / 187

background image

2. Lift the drive out of the drive carrier.

Figure 44. Removing the drive from the drive carrier

Next steps

Install the drive into the drive carrier

.

Installing the drive into the drive carrier

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 26.

2. If installed,

remove the front bezel

.

3.

Remove the drive blank

.

Steps

1. Insert the drive into the drive carrier with the drive connector facing towards the rear of the carrier.
2. Align the screw holes on the drive with the screws holes on the drive carrier.
3. Using a Phillips #1 screwdriver, secure the drive to the drive carrier with the screws.

NOTE:

When installing a drive into the drive carrier, ensure that the screws are torqued to 4 lbf-in.

NOTE:

If the hard drive or SSD carrier has Torx screw, use Torx 6 (for 2.5-inch drive) or Torx 8 (for 3.5-inch drive)

screwdriver to install the drive.

Installing and removing system components

53

«
...
51
52
53
54
55
...
»

Summary of Contents for E68S




























































































































































































Reviews:

No comments

Related manuals for E68S

Express5800/R120h-1E

Brand: NEC Pages: 52

Brand: Aaeon Pages: 38

SuperServer 6041G

Brand: Supero Pages: 114

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Brand: LaCie Pages: 67

Transport TN27 B4987

Brand: TYAN Pages: 135

Brand: Olive Pages: 44

Brand: Supermicro Pages: 118

Brand: IOGear Pages: 44

Brand: ASROCK Rack Pages: 51

SUPERSERVER 1028UX-CR-LL1

Brand: Supermicro Pages: 128

Sun Fire Netra 1280

Brand: Sun Microsystems Pages: 10

Brand: HIKVISION Pages: 31

Brand: Cisco Pages: 23

Brand: Cisco Pages: 75

Brand: Cisco Pages: 132

Brand: Cisco Pages: 58

UCS 6400 Series

Brand: Cisco Pages: 68

Smart Storage NSS322

Brand: Cisco Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands