Dell EMC E68S Installation And Service Manual Download | Manualshive

Page: 53 / 187

background image

2. Lift the drive out of the drive carrier.

Figure 44. Removing the drive from the drive carrier

Next steps

Install the drive into the drive carrier

.

Installing the drive into the drive carrier

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 26.

2. If installed,

remove the front bezel

.

3.

Remove the drive blank

.

Steps

1. Insert the drive into the drive carrier with the drive connector facing towards the rear of the carrier.
2. Align the screw holes on the drive with the screws holes on the drive carrier.
3. Using a Phillips #1 screwdriver, secure the drive to the drive carrier with the screws.

NOTE:

When installing a drive into the drive carrier, ensure that the screws are torqued to 4 lbf-in.

NOTE:

If the hard drive or SSD carrier has Torx screw, use Torx 6 (for 2.5-inch drive) or Torx 8 (for 3.5-inch drive)

screwdriver to install the drive.

Installing and removing system components

53

«
...
51
52
53
54
55
...
»

Summary of Contents for E68S




























































































































































































Reviews:

No comments

Related manuals for E68S

NetVista N2800e

Brand: IBM Pages: 82

Azure StorSimple 8100

Brand: Microsoft Pages: 12

Brand: LaCie Pages: 22

Brand: Yeong Yang Pages: 7

Brand: Devolinx Pages: 51

Virtual Services Platform 7000 Series

Brand: Avaya Pages: 103

Brand: NEC Pages: 408

Brand: TYAN Pages: 106

Brand: IBM Pages: 16

Brand: IBM Pages: 98

DLAP-201 Series

Brand: ADLINK Technology Pages: 39

Brand: Black Box Pages: 30

Brand: t.a.c. Pages: 36

A+ AS -2114GT-DNR

Brand: Supermicro Pages: 126

Compaq AlphaServer DS10

Brand: HP Pages: 43

Cluster Platform Hardware Kits v2010

Brand: HP Pages: 12

Brand: HP Pages: 12

hpe proliant dl20 gen9

Brand: HP Pages: 131

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands